EMC, Power Quality and Protection
TOSHIBA
The following devices are specifically designed to provide protection, reduce EMI and improve the power quality (ie. power factor, harmonic distortion, surge suppression) of Toshiba TOSVERT inverter drives. Please feel free to contact us for more information. We are also able to perform power quality measurements and analysis on-site to help you select the optimal solution that complies with power quality standards or requirements
 
Benefits of Reactors and Filters
　
  • Increase Drive System Reliability
  • Reduce Harmonics
  • Reduce dv/dt (EMC)
  • Reduce Motor Noise and Temperature
  • Improve True Power Factor
  • Filter Power Line Disturbances
  • Reduce Surge Currents
  • Extend Transistor Life
  • Reduce Voltage Doubling Effects
  • Absorb Power Line Spikes
 
Comparison of DC reactor and AC reactor
Reactor Efficiency
Power factor improvement Harmonics reduction External surge voltage reduction
Ac reactor o o o
DC reactor oo oo x
　

AC Reactor
The AC reactor is used to improve the input power factor of the inverter power supply, reduce harmonics and/or suppress external surges. Joint usage of the DC reactor with the AC reactor will provide high reliability operation of TOSVERT inverter for suppressing external surges.
For: All Tosvert series
　
　

DC Reactor
The DC reactor is used to improve the input power factor of the inverter power supply and reduce harmonics. The DC reactor is more effective than the AC reactor in improving the power factor and reduce harmonics.
For: All Tosvert series (some models have built-in DC reactor)
　
　

Harmonic Filter
Harmonic filters specifically designed and tested for TOSVERT inverters can absorb harmonics distortion, resulting in a clearn, near sinusoidal input current supply. Complies with international standards including IEEE519, EN61000-3-4, and HK EMSD's GS2007 THD requirements.
For: All Tosvert series
　

EMI Filter
Most TOSVERT series inverter drives have built-in EMC noise filter. But when you need to comply with a higher standard or connected to long motor cable between inverter drive and motor, please use an external EMI filter.
For: All Tosvert series
　

No Picture
Available

 Braking Resistor
Frequent start-stop operation, sudden braking or when the deceleration time must be shortened on loads with large inertia will generate and dissipate excessive heat energy. The braking resistor is used to absorb the energy.
For: All Tosvert series
　
　
　

MTE
MTE is an international supplier of power quality products designed to improve the reliability of power electronic systems and adjustable frequency drives. MTE manufactures line/load reactors, Matrix® Passive Harmonic Filters, Matrix PureSine® Active Harmonic Filter, EMI/RFI filters, DC link chokes, dv/dt and sine wave motor protection filters, plus numerous custom magnetic products that provide power quality solutions in a broad range of applications.
　

RLW Series 3-phase Line/Load Reactors
Passive reactors help to keep your equipment running longer by absorbing many of the power line disturbances which otherwise damage or shut down your inverters, variable speed controllers, or other sensitive equipment. They are very effective at reducing harmonics produced by inverters and drives and can be used on either the input or output.
For: All Tosvert series
　

Matrix AP Harmonic Filter with MTE's "Adaptive Passive Technology"
Using the adaptive passive technology, the filter adapts to various loads while providing optimized THID performance. It maintains a THID performance of 8% MAX at 30% load and 5% MAX at full load and helps meet IEEE-519 Requirements (5% THID) when used at lighter loads.
For: All Tosvert series
 

Matrix PureSine Active Harmonic Filters from MTE are powerful filtering solutions for coordinated variable load power factor correction (PFC), phase balance correction, and harmonic mitigation. Using PureSine Active Harmonic Filters you can realize less than 5% Total Demand Distortion (TDD) while compensating up to the 51st Harmonic and managing up to 12 different Harmonic Signatures simultaneously.
For: All Tosvert series

　

RFI/EMI Filters
MTE's type "RF" filters offer an economical solution to many facility interference problems caused by the high frequency emissions of adjustable speed motor drives and inverters. Type "RF" filters can prevent drives and inverters from interfering with other sensitive electronic loads by reducing both common mode and differential mode noise emissions.
For: All Tosvert series
　
　
　
Communications
　

TOSHIBA
With one of the broadest sets of supported industrial protocols in the industry, Toshiba drives can easily communicate with your network. With little or no setup required, genuine Toshiba option cards offer an almost plug and play installation and seamlessly integrate into your network. The built-in communication options provides the interface between industrial networks and inverter drives. The communication modular terminal blocks are ideal for space saving and centralized control systems.

　

DEV001Z: DeviceNet Communication Option Board
Built-in DeviceNet interface for VF-S11 inverter
For: Tosvert VF-S11, VF-FS1 
　
　

RS4003Z: RS485 Communication Option Board
Built-in RS485 interface for VF-S11 inverter
For: Tosvert VF-S11, VF-FS1 
　

LIU005Z: LonWorks Communication Option Board
Built-in LonWorks interface for VF-S11 inverter
For: Tosvert VF-S11, VF-FS1
　

Communication Terminal Block Expansion Option
 - DEV002Z: Built in DeviceNet card for VF-AS1/PS1
 - PDP002Z: Built in Profibus DP card for VF-AS1/PS1
 - CCL001Z: Built in CC-Link card for VF-AS1/PS1
For: Tosvert VF-AS1, VF-PS1
　

I/O Terminal Block Expansion Option
 - ETB003Z: 4 digital inputs, 2 digital outputs, 1 relay output, 1 PTC input
 - ETB004Z: all ETB003Z I/O's + 2 analogue inputs & 2 analogue outputs
For: Tosvert VF-AS1, VF-PS1
　

No Picture
Available

 TOS-SN-2: RS485 Communication Interface
External RS-485 Interface
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
　

Industrial Control Communications
Specializing in the engineering and manufacturing of embedded communication and control solutions for factory automation, networked controls, and building automation systems. The ICC Network Gateway Series is designed for Toshiba inverter drives to provide a uniform interface, configuration and application experience. This commonality reduces the user's learning curve, reducing commissioning time while simplifying support.
　

PBDP-110: External Profibus Interface
Provides Profibus connectivity to Toshiba inverter drives.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
　

MBP-100: Modbus Plus Network Gateway
Provides connectivity between Modbus Plus, RS-485 and RS-232 based fieldbus protocols and/or Toshiba inverter drives.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
　

DNET-100: DeviceNet Network Gateway
Provides connectivity between DeviceNet, RS-485 and RS-232 based fieldbus protocols and/or Toshiba inverter drives.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
　

ETH-200: Ethernet Multi-Protocol Network Gateway
Provides connectivity between Ethernet, RS-485 and RS-232 based fieldbus protocols and/or Toshiba inverter drives.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
　
　
　
Remote Keypads & HMI Interfaces
Toshiba allows you to mount your inverter drive somewhere else while keeping the control close to you. With plain English displays and the ability to store drive parameter sets available on some units, these keypads can make it even easier when using your new Toshiba inverter.
　
　
TOS-SN-1: Extension control panel
Display 4 digit LED. Inverter's built-in panel functions.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
　
TOS-SN-10: Extension control panel
Display 4 digit LED. Inverter's built-in panel functions.
For: Tosvert VF-AS1, VF-PS1, VF-nC3, VF-S15
　

RKP001Z: Toshiba Remote control keypad  
Display 4 digit LED. Inverter's built-in panel functions.
For: Tosvert VF-S11, VF-FS1, VF-nC1
　
　

RKP002Z: Toshiba Remote control panel
Display 4 digit LED. Parameter copy & memory function. Easy Key
For: Tosvert VF-AS1, VF-PS1, VF-S11, VF-FS1, VF-nC1
　
　

RKP004Z: Toshiba Remote High Resolution LCD panel
LCD Display w/backlight. Language selection. Jog dial + 4 function keys.
For: Tosvert VF-AS1
　
　
　
　
PC-Link Cables
Connect your Toshiba inverter drive with any PC/notebook using one of the following cable options to configure, operate and monitor the inverter drive with the easy-to-use PCM software. (Note: PCM software is included and available for download)
　
　

TOS-SN-3: RS232/USB PC-Link cable
Data communication between PC's RS232c serial or USB port with inverter drive.
For: Tosvert VF-S11, VF-FS1, VF-nC1　
　

TOS-SN-9: USB PC-Link cable
Data communication between PC's USB port with inverter drive.
For: Tosvert VF-AS1, VF-PS1, VF-nC3, VF-S15
　

USB001Z: USB PC-Link cable
Data communication between PC's USB port with inverter drive.
For: Tosvert VF-AS1, VF-PS1, VF-S11, VF-FS1, VF-AS1, VF-nC1
　
 

　

　 © 2013 Sunnice Supplies Co., Ltd all rights reserved.